Frequency Dependent Material Definition in ANSYS HFSS

By: Sima Noghanian
– October 3, 2019
Categories:

Electromagnetic models, especially those covering a frequency bandwidth, require a frequency dependent definition of dielectric materials. Material definitions in ANSYS Electronics Desktop can include frequency dependent curves for use in tools such as HFSS and Q3D. However, there are 5 different models to choose from, so you may be asking: What’s the difference?

In this blog, I will cover each of the options in detail. At the end, I will also show how to activate the automatic setting for applying a frequency dependent model that satisfies the Kramers-Kronig conditions for causality and requires a single frequency definition.

Background

Recalling that the dielectric properties of material are coming from the material’s polarization

(1)

where D is the electric flux density, E is the electric field intensity, and P is the polarization vector. The material polarization can be written as the convolution of a general dielectric response (pGDR) and the electric field intensity.

(2)

The dielectric polarization spectrum is characterized by three dispersion relaxation regions α, β, and γ for low (Hz), medium (KHz to MHz) and high frequencies (GHz and above). For example, in the case of human tissue, tissue permittivity increases and effective conductivity decreases with the increase in frequency [1].

Fig. 1. α, β and γ regions of dielectric permittivity

Each of these regions can be modeled with a relaxation time constant

(3)

where τ is the relaxation time.

(4)

The well-known Debye expression can be found by use of spectral representation of complex permittivity (ε(ω)) and it is given as:

(5)
(6)

where ε is the permittivity at frequencies where ωτ>>1, εs is the permittivity at ωτ>>1, and j2=-1. The magnitude of the dispersion is ∆ε = εs.

The multiple pole Debye dispersion equation has also been used to characterize dispersive dielectric properties [2]

(7)

In particular, the complexity of the structure and composition of biological materials may cause that each dispersion region be broadened by multiple combinations. In that case a distribution parameter is introduced and the Debye model is modified to what is known as Cole-Cole model

(8)

where αn, the distribution parameter, is a measure of broadening of the dispersion.

Gabriel et. al [3] measured a number of human tissues in the range of 10 Hz – 100 GHz at the body temperature (37℃). This data is freely available to the public by IFAC [4].

Frequency Dependent Material Definition in HFSS and Q3D

In HFSS you can assign conductivity either directly as bulk conductivity, or as a loss tangent. This provides flexibility, but you should only provide the loss once. The solver uses the loss values just as they are entered.

To define a user-defined material choose Tools->Edit Libraries->Materials (Fig. 2). In Edit Libraries window either find your material from the library or choose “Add Material”.

Fig. 2. Edit Libraries screen shot.

To add frequency dependence information, choose “Set Frequency Dependency” from the “View/Edit Material” window, this will open “Frequency Dependent Material Setup Option” that provides five different ways of defining materials properties (Fig. 3).

Fig. 3. (Left) View/Edit Material window, (Right) Frequency Dependent Material Setup Option.

Before choosing a method of defining the material please note [5]:

  • The Piecewise Linear and Frequency Dependent Data Points models apply to both the electric and magnetic properties of the material. However, they do not guarantee that the material satisfies causality conditions, and so they should only be used for frequency-domain applications.
  • The Debye, Multipole Debye and Djordjevic-Sarkar models apply only to the electrical properties of dielectric materials. These models satisfy the Kramers-Kronig conditions for causality, and so are preferred for applications (such as TDR or Full-Wave SPICE) where time-domain results are needed. They also include an automatic Djordjevic-Sarkar model to ensure causal solutions when solving frequency sweeps for simple constant material properties.
  • HFSS and Q3D can interpolate the property’s values at the desired frequencies during solution generation.

Piecewise Linear

This option is the simplest way to define frequency dependence. It divides the frequency band into three regions. Therefore, two frequencies are needed as input. Lower Frequency and Upper Frequency, and for each frequency Relative Permittivity, Relative Permeability, Dielectric Loss Tangent, and Magnetic Loss Tangent are entered as the input. Between these corner frequencies, both HFSS and Q3D linearly interpolate the material properties; above and below the corner frequencies, HFSS and Q3D extrapolate the property values as constants (Fig. 4).

Fig. 4. Piecewise Linear Frequency Dependent Material Input window.

Once these values are entered, 4 different data sets are created ($ds_epsr1, $ds_mur1, $ds_tande1, $ds_tandm1). These data sets now can be edited. To do so choose Project ->Data sets, and choose the data set you like to edit and click Edit (Fig. 5). This data set can be modified with additional points if desired (Fig. 6).

Fig. 5. (Left) Project data set selection, (right) defined data set for the material.
Fig. 6. A sample data set.

Frequency Dependent

Frequency Dependent material definition is similar to Piecewise Linear method, with one difference. After selecting this option, Enter Frequency Dependent Data Point opens that gives the user the option to use which material property is defined as a dataset, and for each one of them a dataset should be defined. The datasets can be defined ahead of time or on-the-fly. Any number of data points may be entered. There is also the option of importing or editing frequency dependent data sets for each material property (Fig. 7).

Fig. 7. This window provides options of choosing which material property is frequency dependent and enter the data set associated with it.

Djordjevic-Sarkar

This model was developed initially for FR-4, commonly used in printed circuit boards and packages [6]. In fact, it uses an infinite distribution of poles to model the frequency response, and in particular the nearly constant loss tangent, of these materials.

(9)

where ε is the permittivity at very high frequency,  is the conductivity at low (DC) frequency,  j2=-1, ωA is the lower angular frequency (below this frequency permittivity approaches its DC value), ωB is the upper angular frequency (above this frequency permittivity quickly approaches its high-frequency permittivity). The magnitude of the dispersion is ∆ε = εs-ε∞.

Both HFSS and Q3D allow the user to enter the relative permittivity and loss tangent at a single measurement frequency. The relative permittivity and conductivity at DC may optionally be entered. Writing permittivity in the form of complex permittivity [7]

(10)
(11)

Therefore, at the measurement frequency one can separate real and imaginary parts

(12)
(13)

where

(14)

Therefore, the parameters of Djordjevic-Sarkar can be extracted, if the DC conductivity is known

(15)

If DC conductivity is not known, then a heuristic approximation is De = 10 εtan δ1.

The window shown in Fig. 8 is to enter the measurement values.

Fig. 8. The required values to calculate permittivity using Djordjevic-Sarkar model.

Debye Model

As explained in the background section single pole Debye model is a good approximation of lossy dispersive dielectric materials within a limited range of frequency. In some materials, up to about a 10 GHz limit, ion and dipole polarization dominate and a single pole Debye model is adequate.

(16)
(17)
(18)
(19)
(20)

The Debye parameters can be calculated from the two measurements [7]

(21)

Both HFSS and Q3D allow you to specify upper and lower measurement frequencies, and the loss tangent and relative permittivity values at these frequencies. You may optionally enter the permittivity at high frequency, the DC conductivity, and a constant relative permeability (Fig. 9).

Fig. 9. The required values for Single Pole Debye model.

Multipole Debye Model

For Multipole Debye Model multiple frequency measurements are required. The input window provides entry points for the data of relative permittivity and loss tangent versus frequency. Based on this data the software dynamically generates frequency dependent expressions for relative permittivity and loss tangent through the Multipole Debye Model. The input dialog plots these expressions together with your input data through the linear interpolations (Fig. 10).

Fig. 10. The required values for Multipole Debye model.

Cole Cole Material Model

The Cole Cole Model is not an option in the material definition, however, it is possible to generate the frequency dependent datasets and use Frequency Dependent option to upload these values. In fact ANSYS Human Body Models are built based on the data from IFAC database and Frequency Dependent option.

Visualization

Frequency-dependent properties can be plotted in a few different ways. In View/Edit Material dialog right-click and choose View Property vs. Frequency. In addition, the dialogs for each of the frequency dependent material setup options contain plots displaying frequency dependence of the properties.

You can also double-click the material property name to view the plot.

Automatically use causal materials

As mentioned at the beginning, there is a simple automatic method for applying a frequency dependent model in HFSS. Select the menu item HFSS->Design Setting, and check the box next to Automatically use casual materials under Lossy Dielectrics tab.

Fig. 11. Causal material can be enforced in HFSS Design Settings.

This option will automatically apply the Djordjevic-Sarkar model described above to objects with constant material permittivity greater than 1 and dielectric loss tangent greater than 0. Keep in mind, not only is this feature simple to use, but the Djordjevic-Sarkar model satisfies the Kramers-Kronig conditions for causality which is particularly preferred for wideband applications and where time-domain results will also be needed. Please note that if the assigned material is already frequency dependent, automatic creation of frequency dependent lossy materials is ignored.

If you would like more information or have any questions about ANSYS products please email info@padtinc.com

References

  • D.T. Price, MEMS and electrical impedance spectroscopy (EIS) for non-invasive measurement of cells, in MEMS for Biomedical Applications, 2012, https://www.sciencedirect.com/topics/materials-science/electrical-impedance
  • W. D. Hurt, “Multiterm Debye dispersion relations for permittivity of muscle,” IEEE Trans. Biomed. Eng, vol. 32, pp. 60-64, 1985.
  • S. Gabriel, R. W. Lau, and C. Gabriel. “The dielectric properties of biological tissues: III. Parametric models for the dielectric spectrum of tissues.” Physics in Medicine & Biology, vol. 41, no. 11, pp. 2271, 1996.
  • Dielectric Properties of Body Tissues in the Frequency Range 10 Hz – 100 GHz, http://niremf.ifac.cnr.it/tissprop/.
  • ANSYS HFSS Online Help, Nov. 2013, Assigning Materials.
  • A. R. Djordjevic, R. D. Biljic, V. D. Likar-Smiljani, and T. K. Sarkar, “Wideband frequency-domain characterization of FR-4 and time-domain causality,” IEEE Trans. on Electromagnetic Compatibility, vol. 43, no. 4, p. 662-667, Nov. 2001.
  • ANSYS HFSS Online Help, 2019, Materials Technical Notes.

Useful Links

PiecewiseLinear Input [4/1/2022: Online manual no longer available, please search your current Ansys help]

DebyeModel Input [4/1/2022: Online manual no longer available, please search your current Ansys help]

MultipoleDebye Model Input [4/1/2022: Online manual no longer available, please search your current Ansys help]

Djordjevic-Sarkar [4/1/2022: Online manual no longer available, please search your current Ansys help]

EnterFrequency Dependent Data Points [4/1/2022: Online manual no longer available, please search your current Ansys help]

ModifyingDatasets [4/1/2022: Online manual no longer available, please search your current Ansys help].

Categories

Certified Elite Channel Partner

Get Your Ansys Products & Support from the Engineers who Contribute to this Blog.

Product Development
Diamond Partner

Technical Expertise to Enable your Addictive Manufacturing Success.

PADT’s Pulse Newsletter

Keep up to date on what is going on at PADT by subscribing to our newsletter.


By submitting this form, you are consenting to receive marketing emails from: Phoenix Analysis and Design Technologies, 7755 S. Research Dr., Tempe, AZ, 85284, https://www.padtinc.com. You can revoke your consent to receive emails at any time by using the SafeUnsubscribe® link, found at the bottom of every email. Emails are serviced by Constant Contact

Share this post:

Share on twitter
Share on facebook
Share on linkedin
Share on pinterest

Upcoming Events

05/26/2022

Modelling liquid cryogenic rocket engines in Flownex - Webinar

05/25/2022

SMR & Advanced Reactor 2022

05/25/2022

05/24/2022

SMR & Advanced Reactor 2022

05/19/2022

RAPID + tct 2022

05/19/2022

Venture Cafe Roundtable: AI & Healthcare

05/18/2022

Tucson after5 Tech Mixer: World View

05/18/2022

RAPID + tct 2022

More Info

05/18/2022

Signal & Power Integrity Updates in Ansys 2022 R1 - Webinar

05/18/2022

Simulation World 2022

05/17/2022

RAPID + tct 2022

05/11/2022

Experience Stratasys Manufacturing Virtual Event

05/04/2022

Mechanical Meshing Updates in Ansys 2022 R1 - Webinar

04/27/2022

04/22/2022

12TH ANNUAL TUCSON GOLF TOURNAMENT

04/21/2022

04/20/2022

Additional Fluids Updates in Ansys 2022 R1

04/20/2022

Experience Stratasys Tour – Tempe Arizona

04/18/2022

Experience Stratasys Tour - Flagstaff Arizona

04/14/2022

D&M West | MD&M West

04/13/2022

D&M West | MD&M West

04/13/2022

Experience Stratasys Tour - Albuquerque New Mexico

04/12/2022

D&M West | MD&M West

04/12/2022

Experience Stratasys Tour - Los Alamos New Mexico

04/12/2022

Optimizing Engineering Workflows f​​​​or Propulsion System Design

04/07/2022

Experience Stratasys Tour - Austin Texas

04/07/2022

37th Space Symposium - Arizona Space Industry

04/06/2022

Transforming Digital Engineering with Ansys Discovery 2022 R1

04/06/2022

37th Space Symposium - Arizona Space Industry

04/05/2022

37th Space Symposium - Arizona Space Industry

04/04/2022

37th Space Symposium - Arizona Space Industry

03/30/2022

Simulation Best Practices for Vehicle Engineering - Webinar

03/23/2022

03/23/2022

High & Low Frequency Electromagnetics Updates in Ansys 2022 R1

02/24/2022

Arizona Technology Council After 5 Tech Mixer "Pandemic Pivot Pizza Pa

02/23/2022

SciTech Festival: Spend an Hour with 3D Printing Experts

02/11/2022

Webinar: Mechanical overview for Ansys 2022 R1

More Info

02/09/2022

Webinar: Product Development 101 (FAKE)

02/08/2022

Webinar: Navigating the Additive Landscape

01/27/2022

Arizona Technology Council 1st Quarter VIP Tech Mixer

More Info

01/26/2022

Simulation Best Practices for Gas Turbine Design & Development - Webin

More Info

01/19/2022

Arizona Photonics Days

More Info

11/04/2021

ExperienceIT, New Mexico

More Info

11/03/2021

Additive Manufacturing & Structural Optimization in Ansys 2021 R2 - We

More Info

11/03/2021

Optics Valley Technical Series: The Future of Simulation in the Optics

More Info

11/02/2021

SBIR Liftoff AZTC Virtual Breakfast Series

More Info

10/10/2021

Stratasys Mobile Truck Stop - Tucson Arizona

More Info

Search in PADT site

Contact Us

Most of our customers receive their support over the phone or via email. Customers who are close by can also set up a face-to-face appointment with one of our engineers.

For most locations, simply contact us: